Rank: Member
Groups: Member
Joined: 7/27/2008(UTC)
Posts: 158
|
I need more information on this . 
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 5/23/2010(UTC)
Posts: 708
Location: Netherlands
Thanks: 2 times
Was thanked: 48 time(s) in 45 post(s)
|
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 7/27/2008(UTC)
Posts: 158
|
I will order and see if I can work it out. Terminals , connexions etc. I will use a switch on the frontplate. Also it would have been nice with a regulator on the board. What is the size off the board ?  
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 5/23/2010(UTC)
Posts: 708
Location: Netherlands
Thanks: 2 times
Was thanked: 48 time(s) in 45 post(s)
|
If that is the question, you likely haven't read page 20 and 47 of the integration guide (revision 1.2.6). I would suggest taking a look. ;)
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 7/27/2008(UTC)
Posts: 158
|
Originally Posted by: LeonvB  If that is the question, you likely haven't read page 20 and 47 of the integration guide (revision 1.2.6). I would suggest taking a look. ;) Sorry then !  Nice document and nice it is smaller then the first Otto. Edited by user Thursday, October 11, 2012 8:04:49 AM(UTC)
| Reason: Not specified
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 10/5/2012(UTC) Posts: 1  Location: st. louis missouri Thanks: 1 times
|
where will i find the integration guide?
thanks
k
|
|
|
|
|
|
Rank: Administration
Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA
Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
|
Originally Posted by: kkerwin where will i find the integration guide?
thanks
k Buffalo page, or the Documents section.
|
 1 user thanked Brian Donegan for this useful post.
|
|
|
|
Rank: Member
Groups: Member
Joined: 7/27/2008(UTC)
Posts: 158
|
My Otto do not work I connected input to B1 and B2 and output to 1 A .
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 7/27/2008(UTC)
Posts: 158
|
Hi do you think my OTTO II is dead ? I connected the S direct to VCC without the 10 kohm resistor ?
|
|
|
|
|
|
Rank: Administration
Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN
Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
|
Doing that alone should not kill it - as long as it was not higher than VCC.
You can easily check the OTTO-II. Just completely disconnect the signals, then use a AA battery and make sure the voltage at the input is present at the output as appropriate.
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 7/27/2008(UTC)
Posts: 158
|
Thank you I will try that . Anyway I ordered anotherone to be sure :). There is no signal trough the Otto II.
|
|
|
|
|
|
Rank: Administration
Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN
Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
|
Did you have VCC connected to 3-5V?
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 7/27/2008(UTC)
Posts: 158
|
|
|
|
|
|
|
Rank: Administration
Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA
Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
|
Do you have the signal grounds connected? It won't work without them.
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 7/27/2008(UTC)
Posts: 158
|
Yes I have . I use 1 B 1 and 1 B 2 for inputs and 1 A for output.
|
|
|
|
|
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
