3 Pages<123> Go to Page...

buffalo 2 lock led dimming Options  Watch this topic  Print this topic  Atom Feed  RSS Feed View » Normal Threaded

Previous Topic Next Topic

back		#21 Posted : Wednesday, January 19, 2011 5:10:10 PM(UTC)
Rank: Member Groups: Member Joined: 8/24/2008(UTC) Posts: 61 Location: greece		Audiblesoundwave wrote: Hi Back, Did you double check the led's orientation? It is a bit fuzzy on the picture but it seems to be in wrong orientation! Good luck, Milton the leds are correct. if they where wrong they wouldn`t light up at all. but anyway the leds are the list of my concern. the problem is that there is no sound at the outputs. i mentioned the led just because i suspect that the problem is that it doesn`t lock the signal.
User Profile View All Posts by User View Thanks

Audiblesoundwave		#22 Posted : Wednesday, January 19, 2011 6:53:40 PM(UTC)
Rank: Advanced Member Groups: Member Joined: 8/3/2010(UTC) Posts: 68 Location: S.F. Bay Area, CA		Sorry Back! I was looking at the MUTE led! The best I can tell from the other 4 pictures that it seems like you installed the IC2 onto the Volumite. I believe a jumper is needed instead of the IC2 for the way you are supplying the power. This may be the problem! Good luck, Milton
User Profile View All Posts by User View Thanks

Brian Donegan		#23 Posted : Wednesday, January 19, 2011 7:12:02 PM(UTC)
Rank: Administration Groups: Administration, Customer Joined: 10/24/2006(UTC) Posts: 2,868 Location: Massachusetts, USA Thanks: 2 times Was thanked: 141 time(s) in 134 post(s)		Hey, good catch. That may indeed be it, as the two vregs would be fighting each other, which would result in a sagging 3.3V VD.
		WWW
User Profile View All Posts by User View Thanks

back		#24 Posted : Thursday, January 20, 2011 4:23:37 PM(UTC)
Rank: Member Groups: Member Joined: 8/24/2008(UTC) Posts: 61 Location: greece		i don`t understand what re you guys saying. the volumite is powered from the ic2 (only) do you suggest i should power it from the psu directly?
User Profile View All Posts by User View Thanks

Brian Donegan		#25 Posted : Thursday, January 20, 2011 4:27:54 PM(UTC)
Rank: Administration Groups: Administration, Customer Joined: 10/24/2006(UTC) Posts: 2,868 Location: Massachusetts, USA Thanks: 2 times Was thanked: 141 time(s) in 134 post(s)		When powered by the I2C connections, the Volumite should not have the voltage regulator (IC2) installed, as it will be trying to regulate a 3.3V supply to 3.3V. The IC2 position on the Volumite should instead have a jumper from pin 1 to pin 3.
		WWW
User Profile View All Posts by User View Thanks

back		#26 Posted : Thursday, January 20, 2011 6:15:13 PM(UTC)
Rank: Member Groups: Member Joined: 8/24/2008(UTC) Posts: 61 Location: greece		Brian Donegan wrote: When powered by the I2C connections, the Volumite should not have the voltage regulator (IC2) installed, as it will be trying to regulate a 3.3V supply to 3.3V. The IC2 position on the Volumite should instead have a jumper from pin 1 to pin 3. never heard that before. anway i don`t think that`s the problem since i disconected the volumite as i told you at the email. tomorrow i will try the dac alone to figure out if the problem is from the buffalo or legato.
User Profile View All Posts by User View Thanks

ustas		#27 Posted : Thursday, March 10, 2011 8:42:24 PM(UTC)
Rank: Member Groups: Member Joined: 3/31/2009(UTC) Posts: 15 Location: Russia		I have same problem. But I do not use Volumite. I have a lock of signal, I have sound, but sound coming distorted, like overdrive with little amplitude. If i make lower current left D1 goes dims. Please help!
User Profile View All Posts by User View Thanks

Russ White		#28 Posted : Thursday, March 10, 2011 9:00:57 PM(UTC)
Rank: Administration Groups: Administration, Customer Joined: 10/24/2006(UTC) Posts: 3,979 Location: Nashville, TN Thanks: 25 times Was thanked: 89 time(s) in 83 post(s)		Any chance you can post photos?
		WWW
User Profile View All Posts by User View Thanks

ustas		#29 Posted : Friday, March 11, 2011 1:59:52 AM(UTC)
Rank: Member Groups: Member Joined: 3/31/2009(UTC) Posts: 15 Location: Russia		Russ, Right now I replaced AVCC RR OP-amp. Now BUF-II and IVY-III workes perfect.
User Profile View All Posts by User View Thanks

Russ White		#30 Posted : Friday, March 11, 2011 6:03:24 AM(UTC)
Rank: Administration Groups: Administration, Customer Joined: 10/24/2006(UTC) Posts: 3,979 Location: Nashville, TN Thanks: 25 times Was thanked: 89 time(s) in 83 post(s)		Ok, very good. Thanks.
		WWW
User Profile View All Posts by User View Thanks

back		#31 Posted : Thursday, March 17, 2011 1:37:29 PM(UTC)
Rank: Member Groups: Member Joined: 8/24/2008(UTC) Posts: 61 Location: greece		brian i received the buffalo with legato. it works fine from balanced outputs but there is no sound from se. it connected the gnd and + from balanced to have se and the sound id distorted. how is it posiible?
User Profile View All Posts by User View Thanks

Russ White		#32 Posted : Thursday, March 17, 2011 1:47:20 PM(UTC)
Rank: Administration Groups: Administration, Customer Joined: 10/24/2006(UTC) Posts: 3,979 Location: Nashville, TN Thanks: 25 times Was thanked: 89 time(s) in 83 post(s)		What are your supply voltages? Did you install the relay backward?
		WWW
User Profile View All Posts by User View Thanks

back		#33 Posted : Thursday, March 17, 2011 2:14:31 PM(UTC)
Rank: Member Groups: Member Joined: 8/24/2008(UTC) Posts: 61 Location: greece		supply voltages are 14.7v anyway i was looking the manual and i think i found the problem. i haven`t install j1-j4 and i give two power supplies. i think i must give the middle too or install the jumpers? Edited by user Thursday, March 17, 2011 2:16:49 PM(UTC)  | Reason: Not specified
User Profile View All Posts by User View Thanks

back		#34 Posted : Thursday, March 17, 2011 2:16:12 PM(UTC)
Rank: Member Groups: Member Joined: 8/24/2008(UTC) Posts: 61 Location: greece		Russ White wrote: What are your supply voltages? Did you install the relay backward? the relay is only for se?
User Profile View All Posts by User View Thanks

Russ White		#35 Posted : Thursday, March 17, 2011 2:22:32 PM(UTC)
Rank: Administration Groups: Administration, Customer Joined: 10/24/2006(UTC) Posts: 3,979 Location: Nashville, TN Thanks: 25 times Was thanked: 89 time(s) in 83 post(s)		Yes you found your problem. The center section is the BAL/SE converter, it must be powered.
		WWW
User Profile View All Posts by User View Thanks

Russ White		#36 Posted : Thursday, March 17, 2011 2:23:12 PM(UTC)
Rank: Administration Groups: Administration, Customer Joined: 10/24/2006(UTC) Posts: 3,979 Location: Nashville, TN Thanks: 25 times Was thanked: 89 time(s) in 83 post(s)		back wrote: Russ White wrote: What are your supply voltages? Did you install the relay backward? the relay is only for se? Yes it is, but I think your problem is more likely that your not powering the BAL/SE section.
		WWW
User Profile View All Posts by User View Thanks

back		#37 Posted : Thursday, March 17, 2011 2:28:22 PM(UTC)
Rank: Member Groups: Member Joined: 8/24/2008(UTC) Posts: 61 Location: greece		so i can use or one power supply or three? if i want to use two maybe i can install only two jumbers?
User Profile View All Posts by User View Thanks

Russ White		#38 Posted : Thursday, March 17, 2011 2:30:27 PM(UTC)
Rank: Administration Groups: Administration, Customer Joined: 10/24/2006(UTC) Posts: 3,979 Location: Nashville, TN Thanks: 25 times Was thanked: 89 time(s) in 83 post(s)		I would not use only two, as you will be asymmetrically loading one. I would use either one or three.
		WWW
User Profile View All Posts by User View Thanks

back		#39 Posted : Thursday, March 17, 2011 2:34:53 PM(UTC)
Rank: Member Groups: Member Joined: 8/24/2008(UTC) Posts: 61 Location: greece		Russ White wrote: I would not use only two, as you will be asymmetrically loading one. I would use either one or three. i thought so. thanks i will make the changes tomorrow.
User Profile View All Posts by User View Thanks

back		#40 Posted : Friday, March 18, 2011 3:42:14 AM(UTC)
Rank: Member Groups: Member Joined: 8/24/2008(UTC) Posts: 61 Location: greece		hi. if i use one psu 360ma is per rail or total?
User Profile View All Posts by User View Thanks

Rss Feed  Atom Feed

Users browsing this topic

GuestUser (11)

3 Pages<123> Go to Page...