Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Login
I/V resistor with Broskie unballancer?
Options
View
Go to last post Go to first unread
Previous Topic Next Topic
Ryssen  
#1 Posted : Thursday, September 22, 2016 6:37:43 PM(UTC)
Ryssen

Rank: Member

Groups: Member
Joined: 1/28/2008(UTC)
Posts: 4
I´m planning on using a Buffalo III SE with a Broskie Unballancer with 12AT7 input tubes and 6cg7 output.
But what I/V resistor should I use? To get about 2volts out.Think
Back to top

Wanna join the discussion?! Login to your Twisted Pear Audio Support forum accountor Register a new forum account.
Back to top  
Ryssen  
#2 Posted : Saturday, September 24, 2016 12:07:33 PM(UTC)
Ryssen

Rank: Member

Groups: Member
Joined: 1/28/2008(UTC)
Posts: 4
Anyone built the unballancer with other tubes and can tell wich I/V resistors used?
Back to top
cdeveza  
#3 Posted : Friday, October 7, 2016 7:20:47 PM(UTC)
cdeveza

Rank: Member

Groups: Member
Joined: 5/12/2016(UTC)
Posts: 66
United States
Location: Concord

Thanks: 6 times
Originally Posted by: Ryssen Go to Quoted Post
Anyone built the unballancer with other tubes and can tell wich I/V resistors used?


I have a dual mono BIIIse, for the output stage I am using diyaudios Quanhao tube I/V, which is similar in topology with broskie's. The resistor I am using is 33 ohms. Not sure if it is actually putting out 2 volts. I actually just experimented with it, started at 1k and slowly goes down. Finally settled on 33 ohms, dont want it to go down too much, dont want to load the DAC too much. The tubes I used are 12AU7 and 6DJ8, with these values and tubes, the sound came out dynamic and well controlled.
Back to top
Ryssen  
#4 Posted : Saturday, October 8, 2016 10:40:11 AM(UTC)
Ryssen

Rank: Member

Groups: Member
Joined: 1/28/2008(UTC)
Posts: 4
Ok,thanks for the answer.
I will start with 50ohm and see how it works,and I changed my mind I will be using 6cg7 for both first and second tube as it has lower mu than 12AT7.
Back to top
cdeveza  
#5 Posted : Monday, October 10, 2016 3:00:51 PM(UTC)
cdeveza

Rank: Member

Groups: Member
Joined: 5/12/2016(UTC)
Posts: 66
United States
Location: Concord

Thanks: 6 times
What I found out from experience is that a system sounds less sterile if you use different tubes between stages, thats why I am using a 12AU7 and a 6DJ8, but thats just me. Good Luck.
Back to top
Ryssen  
#6 Posted : Tuesday, October 11, 2016 7:17:49 PM(UTC)
Ryssen

Rank: Member

Groups: Member
Joined: 1/28/2008(UTC)
Posts: 4
Ok,I will do some tube rolling in the BCF with ecc88 and 12au7.
Back to top
multiblitz  
#7 Posted : Sunday, January 22, 2017 11:19:01 AM(UTC)
multiblitz

Rank: Member

Groups: Member
Joined: 7/2/2008(UTC)
Posts: 13
I am using 20Ohm with my Dual-Mono-Biii, tx2575 preferred. Input tube 12bh7(jj-gold, platinum matched), and 6n6p (not-ev, no gold grid) as ouput tube. No Electrolytics in the psu.
Back to top
Rss Feed  Atom Feed
Users browsing this topic
GuestUser (2)
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Youtube
Copyright © Twisted Pear Audio