Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Login


Options
View
Go to last post Go to first unread
Dragon64  
#1 Posted : Friday, May 6, 2011 7:25:05 PM(UTC)
Dragon64

Rank: Member

Groups: Member
Joined: 5/6/2011(UTC)
Posts: 5
Location: Canada

I can't get the terminal blocks installed on my Buffalo II pcb (24-Apr-2011 shipment), they don't fit the holes. The same terminal blocks fit on the IVY-III pcb though. Pins all measure 41 thou. at widest (tip). I tried wiggling and forcing Brick wall a couple snapped in but not the 5-pin. I'm not wanting to crack the MLCC's so I'll order something...
As someone who has made many PCB's, it could be the plating thickness or layer-stack lineup, but you need more clearance.
I've used Phoenix Contact sliding cage-clamp type MKSDN-1.5/5.08's (~37 thou. pins) and recommend them against these PT-1.5's which have an econo spring that jams when you try disconnect wires.
Russ White  
#2 Posted : Saturday, May 7, 2011 6:35:33 AM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
I will go ahead an increase the drill size a bit, but this is the first I have ever seen this occur. Thanks for the heads up!
Russ White  
#3 Posted : Saturday, May 7, 2011 6:41:31 AM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
You could probably simply clean the holes out a bit with a hand drill, or use a small file on the pins. But certainly the other terminal blocks should fit fine too.
Brian Donegan  
#4 Posted : Saturday, May 7, 2011 6:57:24 AM(UTC)
Brian Donegan

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA

Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
If you drill out the holes, you will likely lose the plate-through in the holes, and may not get proper connectivity to at top-side traces.
Russ White  
#5 Posted : Saturday, May 7, 2011 7:09:03 AM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
Yes do not actually drill them, but you can use a drill to clean off any excess tinning or blobs that might have occurred in the PCB finishing process. Use a drill slightly smaller than the hole diameter for this. Otherwise simply filing a slight point on the TB pins will also do the trick nicely. You can even do this with emery board.
deerinheadlights  
#6 Posted : Saturday, May 7, 2011 9:04:34 AM(UTC)
deerinheadlights

Rank: Member

Groups: Member
Joined: 1/15/2010(UTC)
Posts: 7
Location: Texas

I had the same problem with the (24-Apr-2011shipment). I had leftover terminals from an 13-Mar-2011 shipment and they fit easily.
Dragon64  
#7 Posted : Saturday, May 7, 2011 10:09:11 AM(UTC)
Dragon64

Rank: Member

Groups: Member
Joined: 5/6/2011(UTC)
Posts: 5
Location: Canada

I went through all the terminal blocks in my order and matched a pair that fit Anxious
Sounds like something I'd do with tubes or transistors, lol.
Rss Feed  Atom Feed
Users browsing this topic
GuestUser (5)
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.