Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Login
Fluctuating VR2 (R2) reading ????
Options
View
Go to last post Go to first unread
Previous Topic Next Topic
Audiblesoundwave  
#1 Posted : Thursday, October 7, 2010 8:58:17 PM(UTC)
Audiblesoundwave

Rank: Advanced Member

Groups: Member
Joined: 8/3/2010(UTC)
Posts: 68
United States
Location: S.F. Bay Area, CA
Help!

I am having problem with the BP power module's VR2 (20 ohm) adjustment to .25v and I have already destroyed three VR2. It seems the VR2 is difficult to adjust!

I am using the 200 ohm version (ran out of the 20 ohm version) of the VR2 at the moment; however, the reading is fluctuating (varying from .3 and .214) and not stable at all. The reading would slowly decreasing (to .214) after adjusted to .25v!

I am getting the reading of approx 212 ohm from measuring the VR2’s outer two pins (1 and 3). A reading of approx 212 ohm from pin 1 (right below the adjustment screw) and the middle pin. I don’t think this is right reading.

Could I possibly destroy other components (i.e. Bipolar Power Transistor right next to VR2)? I am running out of solutions due to not having very much of electronic experience!

Thank you for anyone’s input and helps!

Milton
Back to top

Wanna join the discussion?! Login to your Twisted Pear Audio Support forum accountor Register a new forum account.
Back to top  
Russ White  
#2 Posted : Friday, October 8, 2010 8:38:24 AM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
What are you measuring?
Back to top
WWW
Audiblesoundwave  
#3 Posted : Friday, October 8, 2010 9:00:40 AM(UTC)
Audiblesoundwave

Rank: Advanced Member

Groups: Member
Joined: 8/3/2010(UTC)
Posts: 68
United States
Location: S.F. Bay Area, CA
I am measuring R2 for adjusting VR2 to the .25v!

Thanks,
Milton
Back to top
Russ White  
#4 Posted : Friday, October 8, 2010 12:22:19 PM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
Is it connected to any load?

What is the output voltage set at?
Back to top
WWW
Audiblesoundwave  
#5 Posted : Friday, October 8, 2010 9:18:59 PM(UTC)
Audiblesoundwave

Rank: Advanced Member

Groups: Member
Joined: 8/3/2010(UTC)
Posts: 68
United States
Location: S.F. Bay Area, CA
No load yet! The voltage is set at 14.99v (close enough to 15v). 7.45 is for each side.

Thanks,
Milton
Back to top
Brian Donegan  
#6 Posted : Saturday, October 9, 2010 5:04:41 AM(UTC)
Brian Donegan

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA

Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
Audiblesoundwave wrote:
No load yet! The voltage is set at 14.99v (close enough to 15v). 7.45 is for each side.

Thanks,
Milton


I think you may have misunderstood the voltage recommendation. It should be +15V on one side and -15V on the other (each relative to GND). That would be 30V between + and - terminals.
Back to top
WWW
Audiblesoundwave  
#7 Posted : Saturday, October 9, 2010 6:51:44 AM(UTC)
Audiblesoundwave

Rank: Advanced Member

Groups: Member
Joined: 8/3/2010(UTC)
Posts: 68
United States
Location: S.F. Bay Area, CA
Would this misunderstanding cause the fluctuating result of the VR2 adjustment to .25v?

I will try it again with the correct voltage setting of 15v for each of the + and - sides today!

Thanks again,
Milton
Back to top
Rss Feed  Atom Feed
Users browsing this topic
GuestUser (4)
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Youtube
Copyright © Twisted Pear Audio