Twisted Pear Audio Support
»
Product Support
»
Control
»
Volumite Controller
»
Still having some issues with volumite + dual mono buffalo
Rank: Member
Groups: Member
Joined: 2/2/2010(UTC)
Posts: 20
Location: los angeles
|
I must be doing something wrong here.
I received a replacement firmware (labeled all versions) as we had thought that was the initial problem but still having issues with no channel separation and what seems to be a great deal of distortion. It just sounds way way better when not using the volumite.
Here's what I've done:
removed regulator, jumpered pins 1,3
removed controllers from both buffalos
jumpered PB1 to GND on volumite
how it's connected:
B1:dvcc,gnd,sda,scl
B2: gnd,sda,scl
Ideas?
Thanks,
-Ken
|
|
|
|
|
|
Rank: Administration
Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA
Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
|
Can you describe your output wiring? Volumite should in no way cause distortion.
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 2/2/2010(UTC)
Posts: 20
Location: los angeles
|
I don't think it's actual distortion, but perceived distortion due to channel co-mingling or something to that effect. It's like everything comes out of both channels at both times all the time. It's set up with stacked IVYs. I just followed the latest dual-mono diagram with the L and R from each respective buffalo is going to the + on the output of the respective channel, and vice-versa for the -. It sounds great when not using the volumite. Brian Donegan wrote:Can you describe your output wiring? Volumite should in no way cause distortion.
|
|
|
|
|
|
Rank: Member
Groups: Customer
Joined: 10/25/2006(UTC)
Posts: 11
|
yammy1688 wrote:
Here's what I've done:
removed regulator, jumpered pins 1,3
removed controllers from both buffalos
jumpered PB1 to GND on volumite
What is the reason to connect PB1 to GND? I can not find it in volumite manual. Arne
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 2/2/2010(UTC)
Posts: 20
Location: los angeles
|
It's supposed to put it in dual mono mode. 1543 wrote:yammy1688 wrote:
Here's what I've done:
removed regulator, jumpered pins 1,3
removed controllers from both buffalos
jumpered PB1 to GND on volumite
What is the reason to connect PB1 to GND? I can not find it in volumite manual. Arne
|
|
|
|
|
|
Rank: Administration
Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA
Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
|
Jumper ADDR pads on one of the modules?
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 2/2/2010(UTC)
Posts: 20
Location: los angeles
|
Brian Donegan wrote:Jumper ADDR pads on one of the modules? This I haven't done. Does it matter which one? Or perhaps both?
|
|
|
|
|
|
Rank: Administration
Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN
Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
|
The one that will be the right channel.
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 2/2/2010(UTC)
Posts: 20
Location: los angeles
|
When I jumper the ADDR, I just get no sound at all from that channel :(
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 2/2/2010(UTC)
Posts: 20
Location: los angeles
|
Looking at the diagram, it seems like DVCC gets jumpered to ADDRESS? Am I doing this correct by just connect the two pads under ADDR?
|
|
|
|
|
|
Rank: Administration
Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA
Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
|
yammy1688 wrote:Looking at the diagram, it seems like DVCC gets jumpered to ADDRESS? Am I doing this correct by just connect the two pads under ADDR? Yes. It is just setting a bit in the uC to high (DVCC).
|
|
|
|
|
|
Rank: Advanced Member
Groups: Member
Joined: 2/10/2009(UTC)
Posts: 299
Location: Italy
|
Brian Donegan wrote:yammy1688 wrote:Looking at the diagram, it seems like DVCC gets jumpered to ADDRESS? Am I doing this correct by just connect the two pads under ADDR? Yes. It is just setting a bit in the uC to high (DVCC). I was also wondering about this DVCC/ADDRESS trace on the PCB. What if the uC is on the Volumite? Will that jumper still be required? Sorry, but I'm a bit confused...... Cheers, Nic
|
|
|
|
|
|
Rank: Administration
Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN
Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
|
The address jumper is used by the DAC itself to assign its I2C address. It does not have anything do do with the controller except that it dictates what address the controller must communicate with. :) The mono mode volumite sends the left channel instructions to the DAC with the address jumper open(low). It sends the right channel instructions to the one with it closed (high). Cheers! Russ Edited by user Saturday, May 8, 2010 8:37:19 PM(UTC)
| Reason: Not specified
|
|
|
|
|
|
Rank: Administration
Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA
Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
|
Brian Donegan wrote:yammy1688 wrote:Looking at the diagram, it seems like DVCC gets jumpered to ADDRESS? Am I doing this correct by just connect the two pads under ADDR? Yes. It is just setting a bit in the uC to high (DVCC). Sorry for the confusion, I meant DAC, not uC.
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 2/2/2010(UTC)
Posts: 20
Location: los angeles
|
I think I just had one pair of cables reversed on one of the buffalos! Haven't tested it as I've decided to split up the dual mono into single stereo buffalos, but all is well!
|
|
|
|
|
|
Twisted Pear Audio Support
»
Product Support
»
Control
»
Volumite Controller
»
Still having some issues with volumite + dual mono buffalo
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
