Rank: Member
Groups: Member
Joined: 1/1/2010(UTC)
Posts: 8
Location: JP
|
Adjusting the pot has no effect. The volume is always at maximum.
Volumite-to-Opus connections are:
VCC->VD
GND->GND(Power)
GND->GND(Controller)
SDA->SDIN
SCL->SCK
Switch settings:
MODE->open
Everything else is same as mannual's "Recommended Stereo Configuration".
I checked the connections with ohmeter and found no problem. The voltage across VCC and GND of ATTINY85 is about 3.3V.
Any advice would be appreciated.
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 11/9/2007(UTC)
Posts: 453
Location: usa
|
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 1/1/2010(UTC)
Posts: 8
Location: JP
|
Thank you glt. I tried it to no avail. There must be something else too. Interesting blog btw.
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 12/29/2009(UTC)
Posts: 8
|
I have the same issue. USB Receiver, Opus DAC and Volumite. Always max volume. Any tips on how to debug?
|
|
|
|
|
|
Rank: Administration
Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA
Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
|
On the Opus, set all switches to open (center position) except for I2S, which is set to -. On the Volumite, for 96khz pull just PB3 to GND and for 192khz pull PB3 and PB1 to GND. Wire this way: Volumite SCL -> Opus MC Volumite SDA -> Opus MD Volumite GND -> Opus GND Edited by user Friday, March 5, 2010 1:24:36 PM(UTC)
| Reason: Not specified
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 12/29/2009(UTC)
Posts: 8
|
Brian Donegan wrote:On the Opus, set all switches to open (center position) except for I2S, which is set to -.
On the Volumite, for 96khz pull just PB3 to GND and for 192khz pull PB3 and PB1 to GND.
Wire this way:
Volumite SCL -> Opus MC
Volumite SDA -> Opus MD
Volumite GND -> Opus GND
By varios reasons, this has been on hold for a while.. But can you specify what MC and MD on Opus is? I don't see it, neither on the board or other places. Thanks
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 12/29/2009(UTC)
Posts: 8
|
alumin wrote:Brian Donegan wrote:On the Opus, set all switches to open (center position) except for I2S, which is set to -.
On the Volumite, for 96khz pull just PB3 to GND and for 192khz pull PB3 and PB1 to GND.
Wire this way:
Volumite SCL -> Opus MC
Volumite SDA -> Opus MD
Volumite GND -> Opus GND
By varios reasons, this has been on hold for a while.. But can you specify what MC and MD on Opus is? I don't see it, neither on the board or other places. Thanks Wild guess: MD = SDN MC = SCK And Opus GND is G on the controller? Correct?
|
|
|
|
|
|
Rank: Member
Groups: Customer
Joined: 10/25/2006(UTC)
Posts: 2
Location: Houston, Texas USA
|
I have tried to add the Volumite to my OPUS with WM8740.
The DAC plays fine when the jumpers are configured for hardware control.
However with the Volumite controller wired up as shown above, and after checking and rechecking connections and voltages,
all I hear is digital noise coming from the DAC outputs.
When I reconfigure the jumpers for hardware control, the music returns.
Do I have a bad microcontroller?
|
|
|
|
|
|
Rank: Administration
Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN
Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
|
There are two major versions of Opus Volumite code.
One for the WM8740 and one for the WM8741
Are you sure which do you have?
|
|
|
|
|
|
Rank: Member
Groups: Customer
Joined: 10/25/2006(UTC)
Posts: 2
Location: Houston, Texas USA
|
There isn't a label on it, so no I have no idea what's programmed into it. I'll just order another one.
|
|
|
|
|
|
Rank: Advanced Member
Groups: Member
Joined: 12/7/2008(UTC)
Posts: 47
Location: Netherlands
|
Bought a Volumite to try with my Opus, but cant get it to work. connected this way: VCC->VD GND->GND(Power) GND->GND(Controller) SDA->SDIN SCL->SCK Also tried to connect Pb3 to ground as well as both pb3 and pb1 to ground Switches on Opus are open except for I2S which is set to right (-) I get no sound at all. The Opus is fed with a MUX. With no signal (input floating) i get a clean high continuous sound, but still no volume controle. I use the WM8741(stereo) and the firmware is also for WM8741(stereo)(as label indicated) The volumite itself is good as i tried with my Joshua Tree firmware chip. In Hardware mode (default as per manual) al works fine with the Joshua Tree. Could the controller chip have failed? Or am i missing something completely? could there be a fault on the Opus board? Edited by user Tuesday, May 25, 2010 4:52:45 PM(UTC)
| Reason: Not specified
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 11/9/2007(UTC)
Posts: 453
Location: usa
|
|
|
|
|
|
|
Rank: Administration
Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN
Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
|
Which chip is on the Opus?
There are two firmware versions. One for WM8740 and one for WM8741.
|
|
|
|
|
|
Rank: Advanced Member
Groups: Member
Joined: 12/7/2008(UTC)
Posts: 47
Location: Netherlands
|
Its the WM8741
for stereo OPUS firmware
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 1/1/2010(UTC)
Posts: 8
Location: JP
|
I finally got to try Brian's suggestion and it works now. I set I2S switch to the left(-) and that did it. Thanks very much. To zonneveld, Set I2S to left, not right. "Volumite GND -> Power GND" is not necessary as long as you have "Volumite GND -> OPUS GND". Hope this helps. Edited by user Friday, June 11, 2010 3:38:32 AM(UTC)
| Reason: Not specified
|
|
|
|
|
|
Rank: Advanced Member
Groups: Member
Joined: 12/7/2008(UTC)
Posts: 47
Location: Netherlands
|
Thanks TN, I got really confused here.......will try your suggestion asap btw we still need vcc->vd right? Gerard Edited by user Friday, June 11, 2010 3:04:11 PM(UTC)
| Reason: Not specified
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 1/1/2010(UTC)
Posts: 8
Location: JP
|
>btw we still need vcc->vd right?
Right.
|
|
|
|
|
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
