BII Fault !! Seeking help Options  Watch this topic  Print this topic  Atom Feed  RSS Feed View » Normal Threaded

Previous Topic Next Topic

DKL		#1 Posted : Tuesday, September 13, 2011 2:51:38 AM(UTC)
Rank: Member Groups: Member Joined: 5/4/2010(UTC) Posts: 16		Hi All I own 2 x BII in Dual Mono mode. Today,Suddenly out of work and Auto-Mute LED and Lock LED all light-on. Try solve problem like-- 1.Use SPDIF input direct from TOSLINK module 2.Use I2S-GND/D1 input also from TOSLINK module 3.Reset the BII on board But same as before - out of sound Thanks
User Profile View All Posts by User View Thanks

	Wanna join the discussion?! Login to your Twisted Pear Audio Support forum accountor Register a new forum account.

Russ White		#2 Posted : Tuesday, September 13, 2011 2:52:37 PM(UTC)
Rank: Administration Groups: Administration, Customer Joined: 10/24/2006(UTC) Posts: 3,979 Location: Nashville, TN Thanks: 25 times Was thanked: 89 time(s) in 83 post(s)		Both DACs have the same behavior? Can you post images of your setup?
		WWW
User Profile View All Posts by User View Thanks

DKL		#3 Posted : Wednesday, September 14, 2011 9:57:12 PM(UTC)
Rank: Member Groups: Member Joined: 5/4/2010(UTC) Posts: 16		Thanks Russ I break down and switch to stereo mode to try but still same behavior. DKL attached the following image(s): L1020353S.jpg (26kb) downloaded 170 time(s). L1020347S.jpg (25kb) downloaded 167 time(s). You cannot view/download attachments. Try to login or register.
User Profile View All Posts by User View Thanks

pinnocchio		#4 Posted : Thursday, September 15, 2011 6:56:07 AM(UTC)
Rank: Member Groups: Member Joined: 11/3/2010(UTC) Posts: 169 Location: Quebec		How much voltage are you supplying to your DACs? 5.25 volts should be the most. Are you shunting enough current on your PSU?
User Profile View All Posts by User View Thanks

DKL		#5 Posted : Thursday, September 15, 2011 8:34:48 AM(UTC)
Rank: Member Groups: Member Joined: 5/4/2010(UTC) Posts: 16		Yes -Placid supply 5.45V and Shunt 70ma/0.070VDC Thank you
User Profile View All Posts by User View Thanks

LeonvB		#6 Posted : Thursday, September 15, 2011 10:06:52 AM(UTC)
Rank: Member Groups: Member Joined: 5/23/2010(UTC) Posts: 708 Location: Netherlands Thanks: 2 times Was thanked: 48 time(s) in 45 post(s)		How is that measured? On a hot Placid or on a cold one? 5.25V when it's hot is a good measurement for a Placid. 5.45 when it's hot means you're likely going too high for the Tridents when the Placid is still cold. Also, please note you're powering shunt PSUs. A shunt of 50mA is enough, more just generates extra heat.
User Profile View All Posts by User View Thanks

DKL		#7 Posted : Thursday, September 15, 2011 5:34:46 PM(UTC)
Rank: Member Groups: Member Joined: 5/4/2010(UTC) Posts: 16		Measure Plcid ON after 10 min. Try adjust to 5.25V/50ma,same behavoir. Looks like DAC chip gone,Trident 3.28V/3.25V/1.18V and AVCC goes to 3.45V and 3.48V Thnaks Pinnocchio,Thanks LeonvB Edited by user Saturday, September 17, 2011 2:32:29 AM(UTC)  | Reason: Not specified
User Profile View All Posts by User View Thanks

DKL		#8 Posted : Saturday, September 17, 2011 2:37:33 AM(UTC)
Rank: Member Groups: Member Joined: 5/4/2010(UTC) Posts: 16		Hi Russ,Pinnocchio,LeonvB Where and how to replace DAC chips?? Thanks All
User Profile View All Posts by User View Thanks

glt		#9 Posted : Saturday, September 17, 2011 4:52:20 PM(UTC)
Rank: Member Groups: Member Joined: 11/9/2007(UTC) Posts: 453 Location: usa		There is no reason for the DAC chips to be "gone". The tridents should go first, but they are working fine.
		BLOG
User Profile View All Posts by User View Thanks

DKL		#10 Posted : Saturday, September 17, 2011 6:39:23 PM(UTC)
Rank: Member Groups: Member Joined: 5/4/2010(UTC) Posts: 16		Trident and AVCC and Power supply all fine but can't play,by the way the SW1 in all ON. Thanks glt Problem founded. My 2 sets Trident 3.3V x 2, 1.2V x 2 are fault only 2 x 3.3V in normal and replace but same behavoir Appearance of Trident all LED light like normal Thank you glt Edited by user Sunday, September 18, 2011 1:40:08 AM(UTC)  | Reason: Not specified
User Profile View All Posts by User View Thanks

Rss Feed  Atom Feed

Users browsing this topic

GuestUser (2)