Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Login


Options
View
Go to last post Go to first unread
arvema  
#1 Posted : Thursday, December 2, 2010 3:27:00 AM(UTC)
arvema

Rank: Member

Groups: Member
Joined: 10/21/2010(UTC)
Posts: 17
Location: Norway

Thanks: 1 times
After assembling Buffalo II,, IVY II, Volumite and Sympatico in one integrated design, I am experiencing some minor problems. Overall the DAC/amplifier sounds great, wonderful resolution, clarity, warm distinctness in the bass, etc. Thanks for the quality of these products!

My first problem is a weak humming (similar to the sound of my 400VA transformers, located in a separate case). The hum is not influences by turning the Volumite, and it is slightly higher in the left channel. Curiously, when I touch the wires going from Ivy to the left Sympatico, the noise is reduced and changes character. Nothing happens when I touch the SPDIF inlet. But when I turn off power to the Buffalo, the humming disappears completely.

Second problem: I wanted to use both phones and amplifier, but the phone outlet from the + and gnd of the IVY generated scratching sounds, so I had to temporarily remove it, as you can see on the picture. Is it possible to simultaneously drive both phones and amplifier? (My idea was to put a switch on the power inlet of the Sympaticos for selecting only phone use.)
Can someone give me advice how to cope with these issues?

A third issue: Can something be done with noisy transformers, with grounding or something else?

I am a novice in these matters ,d'oh! but still I could not resist experimenting with alternative capacitors, as I got these recommended, (see picture).


arvema attached the following image(s):
Buff2_Ivy2_Sympatico.jpg (125kb) downloaded 184 time(s).

You cannot view/download attachments. Try to login or register.
Brian Donegan  
#2 Posted : Thursday, December 2, 2010 5:03:19 AM(UTC)
Brian Donegan

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA

Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
For the headphone output, you should use the SE and Gnd outputs of the IVY2 if you are using regular (non-balanced) headphones.

The capacitor thing is really not a good idea. You don't want long traces (wires) there. It may be the cause of your noise.

I need to take a closer look at the picture, but the noise you describe sound like a ground loop of a poor connection somewhere.

Overall, it looks like a nice layout.

Edited by user Thursday, December 2, 2010 5:04:11 AM(UTC)  | Reason: Not specified

arvema  
#3 Posted : Thursday, December 2, 2010 2:41:17 PM(UTC)
arvema

Rank: Member

Groups: Member
Joined: 10/21/2010(UTC)
Posts: 17
Location: Norway

Thanks: 1 times
Thanks for fast and helpful reply. Phones are now working fine. I changed capacitors and put a shielded cable on the SPDIF; the hum is clearly reduced, to non-audible on the right, but still quite there on the left channel. I will look further for some poor connection somewhere. Do you have any idea where to try? Is it most likely the Sympatico, or can it also be the IVY or Buffalo?

With the original capacitors the sound is slightly less distinct and transparent. I will find a way to connect the Epcos back without long wires. You should try these once if you have the opportunity.

Two days later: I went over all connections again. Now there is no hum or distrubing noises, and the sound is great!

Edited by user Sunday, December 5, 2010 3:44:21 AM(UTC)  | Reason: Not specified

Rss Feed  Atom Feed
Users browsing this topic
GuestUser (2)
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.