Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Login
Question High current from Placid HD using large off pcb heatsinks? - Questions regarding using a Placid HD v2.1 to power micropc
Options
View
Go to last post Go to first unread
Previous Topic Next Topic
gwikse  
#1 Posted : Friday, May 6, 2016 11:27:29 PM(UTC)
gwikse

Rank: Member

Groups: Member
Joined: 1/19/2011(UTC)
Posts: 332
Location: Oslo, Norway

Thanks: 14 times
Was thanked: 17 time(s) in 17 post(s)
Hello guys.

Lately I have been using raspberry pi as a network streamer. I prefer the sound compared to using amanero usb from a computer with JRMC. But that is another story.

I am thinking of upgrading from a lcdps powering the rpi to a placid hd using large off board heatsinks.
The current consumption on my rpi is far below the 2A that is recommended by the PI guys. From what I understand this is due to the fact that I dont use any USB devices wich is the main power consumer on these miniputers.

I finished building my friends dual mono dac using placid hd to power the two DAC boards that use about 450mA
Using some homemade alu profiles these dont go above 50c, so no problem at all. And that is not even a proper heatsink...

From what I understand from the info on the rpi site I found that my config should require a little more, but not that much more than that. It should be well below 1A, more like 500-600mA

Quote:
Product Recommended PSU current capacity Maximum total USB peripheral current draw Typical bare-board active current consumption
Raspberry Pi Model A 700mA 500mA 200mA
Raspberry Pi Model B 1.2A 500mA 500mA
Raspberry Pi Model A+ 700mA 500mA 180mA
Raspberry Pi Model B+ 1.8A 600mA/1.2A (switchable) 330mA
Raspberry Pi 2 Model B 1.8A 600mA/1.2A (switchable)
Raspberry Pi 3 Model B 2.5A 1.2A ~400mA


My question is: would it be possible to use the placid hd v2.1 with lets say up to 1A when using a large heatsink?

Edited by user Tuesday, May 10, 2016 7:56:20 AM(UTC)  | Reason: Not specified
Back to top

Wanna join the discussion?! Login to your Twisted Pear Audio Support forum accountor Register a new forum account.
Back to top  
gwikse  
#2 Posted : Saturday, May 7, 2016 11:04:10 PM(UTC)
gwikse

Rank: Member

Groups: Member
Joined: 1/19/2011(UTC)
Posts: 332
Location: Oslo, Norway

Thanks: 14 times
Was thanked: 17 time(s) in 17 post(s)
micropc placid psu.jpg (186kb) downloaded 27 time(s).

Edited by user Saturday, May 7, 2016 11:09:10 PM(UTC)  | Reason: Not specified
Back to top
gwikse  
#3 Posted : Tuesday, May 10, 2016 7:55:38 AM(UTC)
gwikse

Rank: Member

Groups: Member
Joined: 1/19/2011(UTC)
Posts: 332
Location: Oslo, Norway

Thanks: 14 times
Was thanked: 17 time(s) in 17 post(s)
Hello? Bump...
Back to top
avr300  
#4 Posted : Thursday, May 12, 2016 7:04:31 PM(UTC)
avr300

Rank: Member

Groups: Member
Joined: 6/17/2008(UTC)
Posts: 921
Denmark

Thanks: 1 times
Was thanked: 70 time(s) in 69 post(s)
If you can keep it cool it will ok.

But do keep an eye on the temperature. Remember to monitor the rectifier bridge a well. It also can run hot.
Back to top
thanks 1 user thanked avr300 for this useful post.
gwikse on 5/13/2016(UTC)
gwikse  
#5 Posted : Friday, May 13, 2016 4:49:33 AM(UTC)
gwikse

Rank: Member

Groups: Member
Joined: 1/19/2011(UTC)
Posts: 332
Location: Oslo, Norway

Thanks: 14 times
Was thanked: 17 time(s) in 17 post(s)
I`ll have a look at it. Perhaps mount it underneath the PCB so that I can use some alu to transfer heat from it to the chassis or something.
Back to top
Rss Feed  Atom Feed
Users browsing this topic
GuestUser (6)
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

Youtube
Copyright © Twisted Pear Audio