Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Login


Options
View
Go to last post Go to first unread
igy137  
#1 Posted : Saturday, September 5, 2015 7:50:48 PM(UTC)
igy137

Rank: Member

Groups: Member
Joined: 10/9/2012(UTC)
Posts: 25
Switzerland

Thanks: 1 times
Hi,

I did some measurements of my Buffalo III build with a R&S UVP analyzer.

The setup is:

Buffalo III, Placid HD 1.0 (modified as per infos on this forum to get rid of ripple), Trident 3.0 + 22uf to eliminate ringing, AVCC latest version, 8-channel mode, i2s isolated, all channels driven with 1kHz sine wave. Note, that control ic was removed and there was no external control, and thus ess chip was running on hardware defaults. For the measurements, only on output channel was connected.

IVY III, Placid HD BP 1.0 (same mods), IVY modified with 0.1% resistors to compensate for 8-channel mode as per integration guide.

I took the following measurements:
- buffalo output directly connected to analyzer, 44khz and 48khz (no ivy connected)
- ivy output to analyzer, 44khz, 48khz, 96khz
- one measurement with 0 input signal

The results, well, not bad, but after seeing Miero's results (at http://mr.ieero.com/pub/...r_Audio_Buffalo_III_DAC/) I was hoping for somewhat better, at least 3rd harmonic content seems to higher than I'd like.

Does this seem reasonable? Any idea improving on 3rd harmonics?

Thanks,
igy

Edited by user Saturday, September 5, 2015 7:52:22 PM(UTC)  | Reason: Not specified

igy137 attached the following image(s):
buf 1khz buf 44k.png (22kb) downloaded 34 time(s).
buf 1khz buf 48k.png (25kb) downloaded 20 time(s).
ivy 1k 44k.png (28kb) downloaded 22 time(s).
ivy 1k 48k.png (28kb) downloaded 29 time(s).
ivy 1k 96k.png (20kb) downloaded 19 time(s).

You cannot view/download attachments. Try to login or register.
miero  
#2 Posted : Sunday, September 6, 2015 3:37:30 PM(UTC)
miero

Rank: Member

Groups: Member
Joined: 10/22/2011(UTC)
Posts: 135
Location: Prague

Thanks: 1 times
Was thanked: 3 time(s) in 3 post(s)
Can you reconfigure analyzer to smaller bandwidth?

Because if you are using 200kHz range, then it has limited dynamic range according to the UPV datasheet.

Dynamic range:
- analog, bandwidth 22 kHz/40 kHz/80 kHz ... 120 dB
- analog, bandwidth 250 kHz ... 100 dB

Source: https://cdn.rohde-schwar...n_0758-1306-12_v0500.pdf
igy137  
#3 Posted : Sunday, September 6, 2015 7:45:10 PM(UTC)
igy137

Rank: Member

Groups: Member
Joined: 10/9/2012(UTC)
Posts: 25
Switzerland

Thanks: 1 times
Hi Miero,
I used 20k bandwidth on all these measurements, am I missing something?
BTW, have you done measurements directly using the buffalo outputs? It'd help finding the root-cause, to see if this distortion is coming from the buffalo itself, or it's the ivy which should perform better?
igy

Edited by user Sunday, September 6, 2015 7:56:13 PM(UTC)  | Reason: Not specified

igy137  
#4 Posted : Sunday, September 13, 2015 8:49:26 PM(UTC)
igy137

Rank: Member

Groups: Member
Joined: 10/9/2012(UTC)
Posts: 25
Switzerland

Thanks: 1 times
I'd highly appreciate some reply from TPA.
I'm mainly interested in the expected 3rd harmonics level without using an I/V stage.

Meanwhile I tried different things to see if I could reduce it somehow:
- replacing the transformer with a 80VA model,
- increasing placid hd C2/C3 value to 100uF,
- using shorter cable between placid hd and bufiii,
- checkig with another audio analyzer

Still, I have the same values, with 1kHz 0dB I2S input: 3rd harmonic level at -80dB, (2nd and all other harmonics are at least 20dB lower).
miero  
#5 Posted : Sunday, September 13, 2015 9:57:49 PM(UTC)
miero

Rank: Member

Groups: Member
Joined: 10/22/2011(UTC)
Posts: 135
Location: Prague

Thanks: 1 times
Was thanked: 3 time(s) in 3 post(s)
Can you check voltages (and possible oscillations) on the AVCC?

Output from ES9018 chip should be determined by AVCC with "zero" at half of AVCC voltage.

Try also different signal levels - if the -80dB is relative to signal.
igy137  
#6 Posted : Tuesday, September 15, 2015 7:03:01 AM(UTC)
igy137

Rank: Member

Groups: Member
Joined: 10/9/2012(UTC)
Posts: 25
Switzerland

Thanks: 1 times
I'm using a brand new, latest version of AVCC, which I checked upon arrival, I saw no signs of oscillation, the voltages were also ok. (I was actually not that happy seeing that the previous AVCC was having quite some ripple, after I already had to 'patch' the Placid HDs, again, because of some ripple...)

Meanwhile I also put back the original microcontroller, to check if running with it would help reducing artifacts, but in fact the 3rd harmonic just stayed there as it was... I'm pretty clueless, where to go / what to check to identify, where does this distortion is coming from.
miero  
#7 Posted : Tuesday, September 15, 2015 7:25:06 AM(UTC)
miero

Rank: Member

Groups: Member
Joined: 10/22/2011(UTC)
Posts: 135
Location: Prague

Thanks: 1 times
Was thanked: 3 time(s) in 3 post(s)
Other ideas:
- check if played signal does not contain that 3rd harmonics
- try to decrease input signal by -1dB if something changes
- check balanced outputs
- check if problem persist on the other digital channels #2-#8
Rss Feed  Atom Feed
Users browsing this topic
GuestUser (2)
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.