Rank: Member
Groups: Member
Joined: 12/21/2011(UTC)
Posts: 6
Location: dk
|
Hi, I bought a used and very well playing 32s DAC, i need som more inputs got the 2 bit selector and 4:1 MUX/DEMUX, i connect the A (MUX/DEMUX) to SPDIF and GND to GND. (With seperate 5v PSU) LEDs shift on the selector works I have dobbelchecked the soldering etc. Good ideas are welcome  ( i'm not sure it actually is intended to work with the 32s  ) /Kurt
|
|
|
|
|
|
Rank: Administration
Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA
Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
|
I think we will need to see your setup/wiring to diagnose. Can you post picture(s)? (It should work fine) Edited by user Monday, December 8, 2014 10:04:34 PM(UTC)
| Reason: Not specified
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 12/21/2011(UTC)
Posts: 6
Location: dk
|
Hello Brian,
Thx for very fast reply, i will post pictures, but i have read a post, in a similar thread, where you advised to isolate the mux and see if there is signalsignal in one. I will try that first..
I have tried, on the 2-bit selector, with and without wiring the J1 jumper, i'm not sure it's supposed to be wired?- it did'nt work without, so i tried with a wire.
I'am a not that experienced with electronics, but i do have with succes made some soldering jobs, but if the other S/PDIF 4:1 MUX/Receiver is an easier task, i will just order a new one.
Btw i have testet the dac without the selector and it's still working :-)
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 12/21/2011(UTC)
Posts: 6
Location: dk
|
Hello again,
New board is now working, nice! - must have fried the old one ;-)
A litle question, i have the 4.1 selection kit also, it,s functioning perfect, but i have a small problem getting knots for the 1/4" shaft, what is the "data" for the selector so i can switch it to one with a 6mm shaft.
Kind regards from af noob from Denmark :-)
|
|
|
|
|
|
Rank: Administration
Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA
Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
|
Originally Posted by: fimpe  Hello again,
New board is now working, nice! - must have fried the old one ;-)
A litle question, i have the 4.1 selection kit also, it,s functioning perfect, but i have a small problem getting knots for the 1/4" shaft, what is the "data" for the selector so i can switch it to one with a 6mm shaft.
Kind regards from af noob from Denmark :-)
http://www.mouser.com/Pr...Z4FwjKj%252b2ufbSQ%3d%3d
|
|
|
|
|
|
Rank: Member
Groups: Member
Joined: 12/21/2011(UTC)
Posts: 6
Location: dk
|
Originally Posted by: Brian Donegan Originally Posted by: fimpe Hello again,
New board is now working, nice! - must have fried the old one ;-)
A litle question, i have the 4.1 selection kit also, it,s functioning perfect, but i have a small problem getting knots for the 1/4" shaft, what is the "data" for the selector so i can switch it to one with a 6mm shaft.
Kind regards from af noob from Denmark :-)
http://www.mouser.com/Pr...Z4FwjKj%252b2ufbSQ%3d%3d THX!!!
|
|
|
|
|
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
