Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Login


Options
View
Go to last post Go to first unread
AudioBear  
#1 Posted : Sunday, March 29, 2015 3:41:40 PM(UTC)
AudioBear

Rank: Member

Groups: Member
Joined: 8/13/2007(UTC)
Posts: 110
Location: UK

Thanks: 8 times
I've going to have to make a few changes in my system and consequently need to ask a few question. Apologies if they seem a bit basic, but everyone has to learn and I'd rather not make any mistakes.

First I'm like to move my sub to the single ended output out of my BII DAC / Legato 3.1. Then I need a way to get single ended out of the balanced Legato outputs. I've not really got enough space for the Ventus & power supply, but the chap who is fixing my amps, suggested the following (see proposed diagram):

1. Is this going to work and be OK?

2. Is it going to be better than the single ended?

3. Is this going to give half of the output on balanced e.g. 0.75v as opposed to 1.5v for single ended?

4. He also suggested I connect a 'inrush current limiter 5A/10 Ohms to ground of Placid HD (going to Legato) to the chassis. Chassis is already earthed to Mains (UK)?

5. Any cap suggestions? Thinking cheaper Obbligato Gold (http://www.hificollective.co.uk/components/obbligato_gold.html) or maybe Auricap or others?

*The resistors inside DAC are because of hum, suspect was when sub and main amp connected to same RCA splitter.*

Balanced Legato DC measurements, powered up as is, but nothing connected to Legato output:

XLR Readings

+ 1(grnd) -> 2(+) = 9.33vdc

+ 1(grnd) -> 3(-) = 9.33vdc

+ 2(+) -> 3(-) = 0.00 vdc

Using the vCap calc these numbers suggest a cap around 0.8uf caps, but I put them in the diagram as 1uf.

Proposed diagram attached

Edited by user Sunday, March 29, 2015 3:43:04 PM(UTC)  | Reason: Not specified

AudioBear attached the following image(s):
Bal-SE.png (100kb) downloaded 34 time(s).

You cannot view/download attachments. Try to login or register.
Brian Donegan  
#2 Posted : Sunday, March 29, 2015 7:34:37 PM(UTC)
Brian Donegan

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA

Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
Why not just use the single-ended outputs of the Legato to supply both the sub and the amps?
AudioBear  
#3 Posted : Monday, March 30, 2015 6:24:47 AM(UTC)
AudioBear

Rank: Member

Groups: Member
Joined: 8/13/2007(UTC)
Posts: 110
Location: UK

Thanks: 8 times
Thanks for your speedy reply Brian, oddly enough this is what I had been doing using a splitter, but it was prone to hum on the new amps. The engineer suggested the solution in the diagram.

Are you saying it won't work, or not work well?
If it will, what of my other questions?
AudioBear  
#4 Posted : Tuesday, March 31, 2015 6:01:30 AM(UTC)
AudioBear

Rank: Member

Groups: Member
Joined: 8/13/2007(UTC)
Posts: 110
Location: UK

Thanks: 8 times
Gentle Bump, anyone - see above posts
Brian Donegan  
#5 Posted : Tuesday, March 31, 2015 1:41:09 PM(UTC)
Brian Donegan

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 2,868
Location: Massachusetts, USA

Thanks: 2 times
Was thanked: 141 time(s) in 134 post(s)
My concern would be level matching your outputs. Other than that, I will defer to your builder's opinion. I would try to fix the ground loop (cause of the hum).

1) Have not tried it this way.

2) I doubt it will be "better," but it may be no worse (see #1)

3) Yes

4) I think he means adding a "ground breaker," which allows you to have your grounds connected to safety earth, but unless there is an actual fault, the grounds remain isolated. I personally keep my low-level signal and low-voltage power grounds isolated from the chassis grounds, but this can be an issue if not done correctly.

5) No. A good quality MKP cap should be fine. I don't use/recommend "boutique" caps. The ones you linked to look reasonable, though I have never used them.
thanks 1 user thanked Brian Donegan for this useful post.
AudioBear on 4/1/2015(UTC)
AudioBear  
#6 Posted : Wednesday, April 1, 2015 2:09:31 PM(UTC)
AudioBear

Rank: Member

Groups: Member
Joined: 8/13/2007(UTC)
Posts: 110
Location: UK

Thanks: 8 times
Removed

Edited by user Friday, April 3, 2015 6:15:01 AM(UTC)  | Reason: Not specified

Rss Feed  Atom Feed
Users browsing this topic
GuestUser (3)
Similar Topics
Which transformers for balanced to single ended conversion on Buffalo32s (Buffalo DAC)
by AudioBear 4/6/2010 2:32:56 AM(UTC)
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.