Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Login


Options
View
Go to last post Go to first unread
branko  
#1 Posted : Saturday, May 5, 2012 4:09:31 PM(UTC)
branko

Rank: Member

Groups: Member
Joined: 3/23/2010(UTC)
Posts: 53
Location: Germany

Thanks: 1 times
Hi,

after upgrading my dual mono buffalo II with two trident sets left channel din not get lock anymore. after flipping right and left buffalo and some measurement it showed that 1 3,3 v trident (VD,GND,VDD at the side of the I2C pins) did not work while the two less did glow well.
Vin is 5,25 V but between GND and VDD i did measure 0 V. I double checked everything, resolderd some points but still nothing. After desoldering the trident and putting back the ferrite in place everything is working fine.

So how to test/measure the trident to identify the problem. I have set up a little power supply with 5,25 V an soldered a dummy load of 47R to GND and Vout.

thx

Branko

Edited by user Saturday, May 5, 2012 4:10:51 PM(UTC)  | Reason: Not specified

Russ White  
#2 Posted : Saturday, May 5, 2012 4:23:36 PM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
Well the simplest thing to try first would be replacing the LED.

Other things to do, measure and record voltages across(not to gnd, but across the part) each resistor.
branko  
#3 Posted : Saturday, May 5, 2012 4:33:50 PM(UTC)
branko

Rank: Member

Groups: Member
Joined: 3/23/2010(UTC)
Posts: 53
Location: Germany

Thanks: 1 times
Voltage across the Resistors:
R1 1,36
R2 0,02
R3 1,92
R4 1,21
R5 0,02
R6 0,0
R7 0,0
R8 1,64
R9 1,12


Why to change the LED? booth are working.

thx

Branko
Russ White  
#4 Posted : Saturday, May 5, 2012 8:07:15 PM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
My mistake, I thought one was not.
Russ White  
#5 Posted : Saturday, May 5, 2012 8:17:13 PM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
On a normally functioning Trident 1 the voltage across R8 and R3 should be the same - or very close.

All of the other voltages seem ok at first glance. So my first suspicion is a dead opamp.

What is the voltage at the output to GND?

Edited by user Saturday, May 5, 2012 8:18:46 PM(UTC)  | Reason: Not specified

branko  
#6 Posted : Saturday, May 5, 2012 8:35:40 PM(UTC)
branko

Rank: Member

Groups: Member
Joined: 3/23/2010(UTC)
Posts: 53
Location: Germany

Thanks: 1 times
The Voltage between GND and Vout is 2,76 V (with resistor 47R as dummy load at Gnd and Vout)

Branko
Russ White  
#7 Posted : Saturday, May 5, 2012 9:05:52 PM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
Ah I see, 47 is a bit low value for this test. Try 75R or 100R.
branko  
#8 Posted : Saturday, May 5, 2012 9:38:20 PM(UTC)
branko

Rank: Member

Groups: Member
Joined: 3/23/2010(UTC)
Posts: 53
Location: Germany

Thanks: 1 times
So now with 100R

R1 1,37
R2 0,02
R3 1,92
R4 1,18
R5 0,03
R6 0,01
R7 0,02
R8 1,92
R9 1,30

Voltage between GND and Vout 3,22

So after chaining the dummy load everything looks OK.
should I put it in again?

Branko
Russ White  
#9 Posted : Saturday, May 5, 2012 9:57:08 PM(UTC)
Russ White

Rank: Administration

Groups: Administration, Customer
Joined: 10/24/2006(UTC)
Posts: 3,979
Location: Nashville, TN

Thanks: 25 times
Was thanked: 89 time(s) in 83 post(s)
Yep, that one looks fine. :)
branko  
#10 Posted : Saturday, May 5, 2012 11:44:06 PM(UTC)
branko

Rank: Member

Groups: Member
Joined: 3/23/2010(UTC)
Posts: 53
Location: Germany

Thanks: 1 times
Thank you,

do not know what it was. must have been some kind of bad joint? After putting it in everything is fine now.

Branko
Rss Feed  Atom Feed
Users browsing this topic
GuestUser (2)
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.