two LEDs on the shunt regulator module blinking, normal? Options  Watch this topic  Print this topic  Atom Feed  RSS Feed View » Normal Threaded

Previous Topic Next Topic

D Yee		#1 Posted : 14 years ago
Rank: Member Groups: Member Joined: 1/2/2011(UTC) Posts: 5 Location: Sacramento, Ca		My B-II is singing so good right at the moment. However, I noticed the two green LEDs on the shunt regulator module mounted directly above the ES9018 keep slightly blinking. Is this normal? Many thanks for your input
User Profile View All Posts by User View Thanks

	Wanna join the discussion?! Login to your Twisted Pear Audio Support forum accountor Register a new forum account.

LeonvB		#2 Posted : 14 years ago
Rank: Member Groups: Member Joined: 5/23/2010(UTC) Posts: 708 Location: Netherlands Thanks: 2 times Was thanked: 48 time(s) in 45 post(s)		I've never seen that with my modules. Is the voltage to the DAC board itself stable?
User Profile View All Posts by User View Thanks

toast		#3 Posted : 14 years ago
Rank: Advanced Member Groups: Member Joined: 3/31/2011(UTC) Posts: 45 Location: Malaysia		Can you measure the voltage supply to it? What you use to supply to BII?
User Profile View All Posts by User View Thanks

D Yee		#4 Posted : 14 years ago
Rank: Member Groups: Member Joined: 1/2/2011(UTC) Posts: 5 Location: Sacramento, Ca		I use one Placid to power the BII. I am feeding the Placid with 10v/2A going in and 5.47v coming out. I calibrated the Placid carefully according to the manual. reading taking at the regulator module regulator-1 in = 5.47v regulator-1 out = 3.50v regulator-2 out = 5.47v regulator-2 out =3.51v It appears the voltage is stable.
User Profile View All Posts by User View Thanks

Russ White		#5 Posted : 14 years ago
Rank: Administration Groups: Administration, Customer Joined: 10/24/2006(UTC) Posts: 3,979 Location: Nashville, TN Thanks: 25 times Was thanked: 89 time(s) in 83 post(s)		I would dial down the placid a bit. Maybe 5.25V. How much current is the placid shunting?
		WWW
User Profile View All Posts by User View Thanks

D Yee		#6 Posted : 14 years ago
Rank: Member Groups: Member Joined: 1/2/2011(UTC) Posts: 5 Location: Sacramento, Ca		I set it to shunt around 50ma as the voltage drop on R3 is about 0.05v. If I dial down to 5.25v, should I calibrate and keep the shunt current to around 50ma? Thanks
User Profile View All Posts by User View Thanks

D Yee		#7 Posted : 14 years ago
Rank: Member Groups: Member Joined: 1/2/2011(UTC) Posts: 5 Location: Sacramento, Ca		Dialed down to 5.25v, no changes.
User Profile View All Posts by User View Thanks

ihear21khz		#8 Posted : 14 years ago
Rank: Member Groups: Member Joined: 7/27/2010(UTC) Posts: 48 Location: Malaysia Was thanked: 1 time(s) in 1 post(s)		Check the both the soldered and mechanical connections between the regulator and the BII board.
User Profile View All Posts by User View Thanks

D Yee		#9 Posted : 14 years ago
Rank: Member Groups: Member Joined: 1/2/2011(UTC) Posts: 5 Location: Sacramento, Ca		I checked all connections before I post, no luck.
User Profile View All Posts by User View Thanks

Rss Feed  Atom Feed

Users browsing this topic

GuestUser